faq:usecamera
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
faq:usecamera [2018/10/22 18:08] caojie |
faq:usecamera [2020/09/21 13:45] (current) |
||
|---|---|---|---|
| Line 32: | Line 32: | ||
| Pic_7\\ | Pic_7\\ | ||
| \\ | \\ | ||
| - | 8. Connect the serial port to the mainboard by press the Connect button, the menu is shown as Pic_8. | + | 8. Connect the serial port to the mainboard by press the Connect button, the menu is shown as Pic_8.\\ |
| - | + | {{: | |
| - | Pic_8 | + | Pic_8\\ |
| - | 9. Select the Xiao_Fei_Long_1103.gco file by press the file. It will looks like Pic_9 below | + | \\ |
| - | + | 9. Select the Xiao_Fei_Long_1103.gco file by press the file. It will looks like Pic_9 below\\ | |
| - | Pic_9 | + | {{: |
| - | 10. Press the Print button, then it will print the selected file as shown as Pic_10 | + | Pic_9\\ |
| - | + | \\ | |
| - | Pic_10 | + | 10. Press the Print button, then it will print the selected file as shown as Pic_10\\ |
| - | 11. By the way, you can also upload your G code file to the printer by using upload function like Pic_11 Pic_12. | + | {{: |
| - | + | Pic_10\\ | |
| - | | + | \\ |
| - | Notice: | + | 11. By the way, you can also upload your G code file to the printer by using upload function like Pic_11 Pic_12.\\ |
| - | A. The upload file format must be .gcode or .stl | + | {{: |
| - | B. If you upload .stl format is file, you will change the .stl to .gcode by pressing the red area like Pic_13 show below. | + | Pic_11\\ |
| - | + | {{: | |
| - | Pic_13 | + | Pic_12\\ |
| - | After that the module will slice the .stl into .gco, you only need to wait for several seconds. It looks like Pic_14.You only need to make sure the output file name show in red area. | + | \\ |
| - | + | Notice:\\ | |
| - | Pic_14 | + | A. The upload file format must be .gcode or .stl\\ |
| - | After press the Slice button, it will be shown like Pic_15 while slicing the file, you need to wait for the slicing complete. The final Menu looks like Pic_16. | + | B. If you upload .stl format is file, you will change the .stl to .gcode by pressing the red area like Pic_13 show below.\\ |
| - | + | {{: | |
| - | Pic 15 Pic_16 | + | Pic_13\\ |
| + | \\ | ||
| + | After that the module will slice the .stl into .gco, you only need to wait for several seconds. It looks like Pic_14.You only need to make sure the output file name show in red area.\\ | ||
| + | {{: | ||
| + | Pic_14\\ | ||
| + | \\ | ||
| + | After press the Slice button, it will be shown like Pic_15 while slicing the file, you need to wait for the slicing complete. The final Menu looks like Pic_16.\\ | ||
| + | {{: | ||
| + | Pic 15\\ | ||
| + | {{: | ||
| + | Pic_16\\ | ||
| + | \\ | ||
| Wish you can connect the rj45 well. If need any support or any other questions, | Wish you can connect the rj45 well. If need any support or any other questions, | ||
faq/usecamera.1540202888.txt.gz · Last modified: 2020/09/21 13:43 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
