set_up_wifi_network:tina2
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
set_up_wifi_network:tina2 [2019/09/26 15:56] peter |
set_up_wifi_network:tina2 [2022/05/18 11:11] (current) ayumi |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | =====How to print with APP：===== | + | ======Set up Wi-Fi network====== |
| - | ====Notices for Network Setting：==== | + | |
| + | ===== Notices for Network Setting： ===== | ||
| + | |||
| + | - It is not possible to use the 5GWiFi network. It needs to operate at 2.4 GHz network frequency. | ||
| - Mobile phones need to be operated with WIFI | - Mobile phones need to be operated with WIFI | ||
| - Local WiFi connection recommendation should not exceed 10 devices | - Local WiFi connection recommendation should not exceed 10 devices | ||
| - | - It is not possible to use the 5GWiFi network. It needs to operate at 2.4 GHz network frequency. | ||
| - When installing, you need to give the mobile APP network location permission. | - When installing, you need to give the mobile APP network location permission. | ||
| - Printers need to be connected in a good network environment (mobile WIFI interface can be used to check whether the network environment is generally above) | - Printers need to be connected in a good network environment (mobile WIFI interface can be used to check whether the network environment is generally above) | ||
| - WiFi name cannot be used in Chinese | - WiFi name cannot be used in Chinese | ||
| - | - If you have any questions about the printer, please contact us. Our email address is：salesservice@wiibooxtech.com | + | - If you have any questions about the printer, please contact us. Our email address is：support@weedo3d.com |
| - | ====Method 1. Using the APP distribution network==== | + | |
| - | ====Download | + | ===== Method 1:Set up WiFi with Wiibuilder(Windows) ===== |
| - | App download: [[http:// | + | |
| - | ===After the download | + | You can also use the Wiibuilder to set the IP for your printer.\\ |
| - | ===Step | + | \\ |
| + | Step1: | ||
| + | \\ | ||
| + | Step2: Click “WLAN Connection”-“WiFi Profile”.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step3: Enter your network password，click “Save”, save to TF card.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: Turn on the 3D printer，print" | ||
| + | {{: | ||
| + | \\ | ||
| + | Step5: After WIFI is connected | ||
| + | ===== Method 2: Manual editing ===== | ||
| + | Step1: | ||
| + | {{ : | ||
| + | \\ | ||
| + | Step2: Enter your home 2.4G network name and network password, save to TF card.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step3: Turn on the 3D printer，print “wifi.gcode”.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: After WIFI is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
| + | \\ | ||
| + | ===== Method 3: Using the APP distribution network ===== | ||
| + | Step1: Download the Andriod APP-Poloprint for the first time.\\ | ||
| + | {{ : | ||
| + | \\ | ||
| + | Step2: Search the network for the corresponding serial number.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | \\ | ||
| + | Step3: After the download is completed, the installation is completed.Open the APP，click" | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: Restart the machine. After WIFI is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
| + | \\ | ||
set_up_wifi_network/tina2.1569484578.txt.gz · Last modified: 2020/09/21 13:43 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
