set_up_wifi_network:tina2
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
set_up_wifi_network:tina2 [2022/05/07 10:26] ayumi old revision restored (2020/09/21 06:45) |
set_up_wifi_network:tina2 [2022/05/18 11:11] (current) ayumi |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | =====Set up Wi-Fi network：===== | + | ======Set up Wi-Fi network====== |
| - | ====Notices for Network Setting：==== | + | |
| + | ===== Notices for Network Setting： ===== | ||
| - It is not possible to use the 5GWiFi network. It needs to operate at 2.4 GHz network frequency. | - It is not possible to use the 5GWiFi network. It needs to operate at 2.4 GHz network frequency. | ||
| - Mobile phones need to be operated with WIFI | - Mobile phones need to be operated with WIFI | ||
| Line 8: | Line 10: | ||
| - WiFi name cannot be used in Chinese | - WiFi name cannot be used in Chinese | ||
| - If you have any questions about the printer, please contact us. Our email address is：support@weedo3d.com | - If you have any questions about the printer, please contact us. Our email address is：support@weedo3d.com | ||
| - | ====Method 1. Using the APP distribution network==== | ||
| - | ====Download the Andriod APP-Poloprint1.3.1 for the first time==== | ||
| - | App download: [[http:// | ||
| - | ===After the download is completed, the installation is completed. After the installation is completed, the first time the application is opened, the interface is displayed. The wizard interface is an introduction to the use of instructions on the app. The specific usage requires a tutorial corresponding to the specific model. This tutorial is for Tina2=== | ||
| - | ===Step 1: Enter the WIFI password in the network where the mobile APP brush WIFI settings interface (do not click OK first)=== | ||
| + | ===== Method 1:Set up WiFi with Wiibuilder(Windows) ===== | ||
| + | |||
| + | You can also use the Wiibuilder to set the IP for your printer.\\ | ||
| + | \\ | ||
| + | Step1: After the computer is connected to the 2.4G network, open the Wiibuilder, | ||
| + | \\ | ||
| + | Step2: Click “WLAN Connection”-“WiFi Profile”.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step3: Enter your network password，click “Save”, save to TF card.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: Turn on the 3D printer，print" | ||
| + | {{: | ||
| + | \\ | ||
| + | Step5: After WIFI is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
| + | |||
| + | ===== Method 2: Manual editing ===== | ||
| + | Step1: | ||
| + | {{ : | ||
| + | \\ | ||
| + | Step2: Enter your home 2.4G network name and network password, save to TF card.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step3: Turn on the 3D printer，print “wifi.gcode”.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: After WIFI is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
| + | \\ | ||
| + | ===== Method 3: Using the APP distribution network ===== | ||
| + | Step1: Download the Andriod APP-Poloprint for the first time.\\ | ||
| + | {{ : | ||
| + | \\ | ||
| + | Step2: Search the network for the corresponding serial number.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | \\ | ||
| + | Step3: After the download is completed, the installation is completed.Open the APP，click" | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: Restart the machine. After WIFI is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
| + | \\ | ||
set_up_wifi_network/tina2.1651890368.txt.gz · Last modified: 2022/05/07 10:26 by ayumi
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
