User Tools

Site Tools


x40:firmware

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
x40:firmware [2020/08/28 16:54]
peter created
x40:firmware [2021/08/16 10:51] (current)
peter
Line 3: Line 3:
 ====Machine Firmware==== ====Machine Firmware====
  
-X40 V1.0.13 <WRAP center round download 50%> \\ +===X40 V1.2.0=== 
-[[http://https://drive.google.com/file/d/1jNDHP-oR3qcjOo097zFuXtbEMz5zhT21/view?usp=sharing|x40Firmware_V1.0.13]]\\+1Add the Baby Z offset in the printing interface, you can set baby Z offset when you printing.\\ 
 +{{:x40:pasted:20210816-034324.png}}\\ 
 +2. Add the dual Nozzle switch function in the printing interface.\\ 
 +{{:x40:pasted:20210816-034442.png}} 
 +3. Add the function that: when the runout sensor trigger, the printing extruder will switch to another extruder\\ 
 +4. Add the Y direction ''XY Offset'' Coarse adjustment.\\ 
 +5. Fixed an issue where bias parameters could not be saved.\\ 
 +6. Fixed the problem of abnormal start-up and continuous call.\\ 
 +7. Fixed an issue where there was no push message after the printing was completed.\\ 
 +8. Fixed the problem of the unlimited position of the switch in Jog mode.\\ 
 +9. Fixed the problem that the missing material wire will be reported if there is no material wire in the extruder on the other side when printing the single sprinkler model.\\ 
 +10. Fixed the problem that the left sprinkler returned to the drawing wire after the execution of the G28 instruction.\\ 
 +11. Fixed an issue where you can't continue to print in copy and mirror mode.\\ 
 +12. Fixed a problem where the right extruder did not return to position after printing was paused in copy and mirror mode.\\ 
 +13. Fixed an issue where the right fan started abnormally when the left fan was started in automatic docking mode.\\ 
 +14. Fixed an issue where the X coordinate offset was not reset after copying and mirroring mode printing.\\ 
 + 
 +<WRAP center round download 30%> \\ 
 +[[https://drive.google.com/file/d/1tgR3ZOb12C5CkBzZ6JJTWC0anIgIMakU/view?usp=sharing|X40Firmware_V1.2.0]]\\ 
 +</WRAP> 
 +  
 + 
 +===X40 V1.1.2=== 
 +1. Fixed an issue where the zoffset parameters were emptied after the factory settings were restored.\\ 
 +2. Modify the prompt message for height adjustment of double sprinklers.\\ 
 +3. Fixed the problem that there is no prompt message in the adjustment interface of the proximity switch.\\ 
 +4. Increase the position of the sprinkler in the X direction before resuming printing.\\ 
 +5. When printing a WiFi disk file, clicking Settings will display a prompt that the parameters cannot be set.\\ 
 + 
 + <WRAP center round download 30%> \\ 
 +[[https://drive.google.com/file/d/1Bn75TvYL3lOoF4kiTnegP5aU__rQMvEF/view?usp=sharing|X40Firmware_V1.1.2]]\\ 
 +</WRAP> 
 + 
 + 
 +===X40 V1.1.1=== 
 + 
 + <WRAP center round download 30%> \\ 
 +[[https://drive.google.com/file/d/1GBbahzHxVB04cAK5WC502RB98z_BrVUE/view?usp=sharing|X40Firmware_V1.1.1]]\\ 
 +</WRAP> 
 + 
 + 
 +===X40 V1.1.0=== 
 + 
 +1. When modifying the nozzles switch, the feed filament parameter is M217 S16 E5 P600 R3000.\\ 
 +2. Double nozzle switch, slow movement distance of right nozzle increases 10mm.\\ 
 +3. The waiting time of 2 seconds after entering the filament when the dual nozzle switch is turned off.\\ 
 +4. Fixed the problem that the automatic filament feeding time returns and the material filament pull back 100mm.\\ 
 +5. Fixed the problem that the extruder motor was locked after the automatic entry and exit filament.\\ 
 +6. Fixed an issue where the shutdown could not be saved.\\ 
 +7. Fixed the problem of continuous call due to power outage.\\ 
 +8. Fixed the problem that Chinese documents could not be printed.\\ 
 +9. Fixed incorrect display of keys in the WiFi disk file preview interface\\ 
 + 
 + <WRAP center round download 30%> \\ 
 +[[https://drive.google.com/file/d/1Hw6I3oYN4YimSE-w89WYUSzT1JDQTqyo/view?usp=sharing|X40Firmware_V1.1.0]]\\ 
 +</WRAP> 
 + 
 + 
 +===X40 V1.0.15=== 
 +1.Match Wiibuilder V2.1.0.2. 
 +2. After removing the nozzle and switching to the model, the filament feed operation is performed. 
 + 
 + <WRAP center round download 30%> \\ 
 +[[https://drive.google.com/file/d/1jNDHP-oR3qcjOo097zFuXtbEMz5zhT21/view?usp=sharing|X40Firmware_V1.0.16]]\\ 
 +</WRAP> 
 + 
 +====UI Firmware For X40==== 
 + 
 + <WRAP center round download 30%> \\ 
 +[[https://drive.google.com/drive/folders/14IAW-FcK0mNDHsk2-_27CFwkX_mi3A6q?usp=sharing|X40_UI]]\\
 </WRAP> </WRAP>
  
x40/firmware.1598604866.txt.gz · Last modified: 2020/09/21 13:43 (external edit)