Differences

This shows you the differences between two versions of the page.

--- x40:firmware [2020/10/23 15:37]
peter
+++ x40:firmware [2021/08/16 10:51] (current)
peter
@@ Line 2: / Line 2: @@
 ====Machine Firmware====
+===X40 V1.2.0===
+. Add the Baby Z offset in the printing interface, you can set baby Z offset when you printing.\\
+{{:x40:pasted:20210816-034324.png}}\\
+. Add the dual Nozzle switch function in the printing interface.\\
+{{:x40:pasted:20210816-034442.png}}
+. Add the function that: when the runout sensor trigger, the printing extruder will switch to another extruder\\
+. Add the Y direction ''XY Offset'' Coarse adjustment.\\
+. Fixed an issue where bias parameters could not be saved.\\
+. Fixed the problem of abnormal start-up and continuous call.\\
+. Fixed an issue where there was no push message after the printing was completed.\\
+. Fixed the problem of the unlimited position of the switch in Jog mode.\\
+. Fixed the problem that the missing material wire will be reported if there is no material wire in the extruder on the other side when printing the single sprinkler model.\\
+. Fixed the problem that the left sprinkler returned to the drawing wire after the execution of the G28 instruction.\\
+. Fixed an issue where you can't continue to print in copy and mirror mode.\\
+. Fixed a problem where the right extruder did not return to position after printing was paused in copy and mirror mode.\\
+. Fixed an issue where the right fan started abnormally when the left fan was started in automatic docking mode.\\
+. Fixed an issue where the X coordinate offset was not reset after copying and mirroring mode printing.\\
+<WRAP center round download 30%> \\
+[[https://drive.google.com/file/d/1tgR3ZOb12C5CkBzZ6JJTWC0anIgIMakU/view?usp=sharing|X40Firmware_V1.2.0]]\\
+</WRAP>
+===X40 V1.1.2===
+. Fixed an issue where the zoffset parameters were emptied after the factory settings were restored.\\
+. Modify the prompt message for height adjustment of double sprinklers.\\
+. Fixed the problem that there is no prompt message in the adjustment interface of the proximity switch.\\
+. Increase the position of the sprinkler in the X direction before resuming printing.\\
+. When printing a WiFi disk file, clicking Settings will display a prompt that the parameters cannot be set.\\
+ <WRAP center round download 30%> \\
+[[https://drive.google.com/file/d/1Bn75TvYL3lOoF4kiTnegP5aU__rQMvEF/view?usp=sharing|X40Firmware_V1.1.2]]\\
+</WRAP>
+===X40 V1.1.1===
+ <WRAP center round download 30%> \\
+[[https://drive.google.com/file/d/1GBbahzHxVB04cAK5WC502RB98z_BrVUE/view?usp=sharing|X40Firmware_V1.1.1]]\\
+</WRAP>
 ===X40 V1.1.0===
-. When modifying the sprinkler switch, the feed wire parameter is M217 S16 E5 P600 R3000.
+. When modifying the nozzles switch, the feed filament parameter is M217 S16 E5 P600 R3000.\\
-. Double sprinkler switch, slow movement distance of right sprinkler increases 10mm.
+. Double nozzle switch, slow movement distance of right nozzle increases 10mm.\\
-. The waiting time of 2 seconds after entering the wire when the double sprinkler switch is turned off.
+. The waiting time of 2 seconds after entering the filament when the dual nozzle switch is turned off.\\
-. Fixed the problem that the automatic wire feeding time returns and the material wire pulls back 100mm.
+. Fixed the problem that the automatic filament feeding time returns and the material filament pull back 100mm.\\
-. Fixed the problem that the extruder motor was locked after the automatic entry and exit wire.
+. Fixed the problem that the extruder motor was locked after the automatic entry and exit filament.\\
-. Fixed an issue where the shutdown could not be saved.
+. Fixed an issue where the shutdown could not be saved.\\
-. Fixed the problem of continuous call due to power outage.
+. Fixed the problem of continuous call due to power outage.\\
-. Fixed the problem that Chinese documents could not be printed.
+. Fixed the problem that Chinese documents could not be printed.\\
-. Fixed incorrect display of keys in the WiFi disk file preview interface
+. Fixed incorrect display of keys in the WiFi disk file preview interface\\
  <WRAP center round download 30%> \\
@@ Line 28: / Line 70: @@
 </WRAP>
-====UI For X40====
+====UI Firmware For X40====
  <WRAP center round download 30%> \\

User Tools

Site Tools

Differences

Page Tools