x40:howto_set_up_wifi_network
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
x40:howto_set_up_wifi_network [2022/04/21 13:50] ayumi |
x40:howto_set_up_wifi_network [2022/04/21 15:31] (current) ayumi |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | =====Set up WiFi Network===== | + | ======Set up WiFi Network====== |
| - | **You have purchased our Independent Dual Extruder 3D printer X40 LOL.// | ||
| - | Here is the method to Setup the Wifi Network For X40** | ||
| - | {{pdfjs 800px > : | + | You have purchased our Independent Dual Extruder 3D printer X40 LOL. |
| - | {{pdfjs 800px > : | + | Here is the method to Setup the Wifi Network For X40 |
| - | + | \\ | |
| - | **If you still have questions, please contact our customer service. Email:salesservice@wiibooxtech.com** | + | If you still have questions, please contact our customer service. Email: |
| + | \\ | ||
| + | WIFICAM(The name of our wifi equipment)wireless network has two working modes:AP mode and STA mode. | ||
| + | You can use AP mode to set the IP for your printer.\\ | ||
| + | \\ | ||
| + | **Notice: | ||
| + | \\ | ||
| + | =====Set up WiFi with webpage===== | ||
| + | Step1: The name of the hotspot SSID is " | ||
| + | \\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step2: Use your computer or mobile phone connect this WiFi.\\ | ||
| + | \\ | ||
| + | Step3: Use a browser(the browser on the device used in Step2)to access http://10.10.0.1: | ||
| + | \\ | ||
| + | Then you can access to the WiFi network management page.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step4: On this page ,it can automatically scan the nearby WiFi network.Click on your network name, enter your WiFi password, and wait for a moment, WIFICAM will try to connect to the network.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step5: After WIFICAM is connected to the Internet, the obtained IP address will be displayed on the printer screen.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | =====Set up WiFi with Wiibuilder(Windows)===== | ||
| + | You can also use the Wiibuilder to set the IP for your printer.\\ | ||
| + | \\ | ||
| + | Step1: After the computer is connected to the network, open the Wiibuilder.\\ | ||
| + | \\ | ||
| + | Step2: Click “WLAN Connection”-“WiFi Profile”.\\ | ||
| + | {{: | ||
| + | {{: | ||
| + | \\ | ||
| + | Step3: Enter your network password，click “Save”, save to TF card.\\ | ||
| + | {{:set_up_wifi_network: | ||
| + | \\ | ||
| + | Step4: Turn on the 3D printer，print “wifi.gcode”.\\ | ||
| + | {{: | ||
| + | \\ | ||
| + | Step5: After WIFICAM is connected the Internet, the obtained IP address will be displayed on the printer screen. | ||
x40/howto_set_up_wifi_network.1650520254.txt.gz · Last modified: 2022/04/21 13:50 by ayumi
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
