Differences

This shows you the differences between two versions of the page.

--- x40:octoprint [2023/01/30 13:57]
mao [3.Reboot your Raspberry Pi and Connect the printer with its baud rate]
+++ x40:octoprint [2023/01/31 14:58] (current)
mao
@@ Line 8: / Line 8: @@
  =====Our Customized OctoPi=====
 This is the easiest way to use OctoPrint on a Raspberry Pi\\
-====Download Image====
+====1.Download Image====
 [[https://github.com/WEEDO3DTECH/OctoPi/releases/download/v1.8.6/2022-09-22-raspios-bullseye-armhf-lite-eww.xz|Download our custom version of OctoPi]] .\\
-====Install image tool====
+====2.Install image tool====
-Download the latest version of [[https://www.raspberrypi.com/software/|Raspberry Pi Imager]] and install it. If you want to use Raspberry Pi Imager from a second Raspberry Pi, you can install it from a terminal using **sudo apt install rpi-imager**\\
+Download the latest version of [[https://www.raspberrypi.com/software/|Raspberry Pi Imager]] and install it. \\
-====Flash image====
+====3.Flash image====
 Then:
   *Connect an SD card reader with the SD card inside.
@@ Line 18: / Line 18: @@
   *Choose the SD card you wish to write your image to.
   *Review your selections and click on the Write button to begin writing data to the SD Card.
+====4.Connect Printer====
+Select X40 from the "Printer Profile" settings, and connect the printer with 115200 baud rate.
+{{:octoprint:x40-octoprint-connect.png?600|}}\\
 ----
@@ Line 43: / Line 46: @@
   wget http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel-headers_1.20201126-1_armhf.deb
 （If your Linux kernel version is not 5.4.79, download the corresponding one from http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/ ; \\
-Use this command to check which version of your Linux kernel: **uname -r**）\\
+Use this command to check which version of your Linux kernel is: **uname -r**）\\
 \\
 Install the header file :
@@ Line 49: / Line 52: @@
 {{:octoprint:4install-header.png?400|}}
-===b)Download the CH340 serial driver source code and unzip it===
+===b)Download the CH340/CH341 serial driver source code and unzip it===
   wget http://www.weedo3dprinter.com/lib/exe/fetch.php/firmware/ch341ser_linux-kernel5.4.79.zip
   unzip ch341ser_linux-kernel5.4.79.zip
@@ Line 62: / Line 65: @@
   sudo depmod
 {{:octoprint:7copy.png?400|}}
 ====5.Reboot your Raspberry Pi and Connect the printer with its baud rate====
-{{:octoprint:8tina2s-connect.png?600|}}
+===a)Reboot your Raspberry Pi, then add X40 settings to the profile.===
+{{:octoprint:x40-octoprint-settings_1_.png?400|}}
+{{:octoprint:x40-octoprint-settings_2_.png?400|}}
+{{:octoprint:x40-octoprint-settings_3_.png?400|}}
+{{:octoprint:x40-octoprint-settings_4_.png?400|}}
+===b)Connect printer with 115200 baud rate===
+{{:octoprint:x40-octoprint-connect.png?600|}}\\
 ----
 =====Install OctoPrint from source on a Raspberry Pi=====
-This installation method is a bit complicated, if you do not have programming skills, we do not recommend you to use this method
+This installation method is a bit complicated, if you do not have programming skills, we do not recommend you to use this method.
 ====1.Install OctoPrint====
 Install OctoPrint following the [[https://community.octoprint.org/docs|OctoPrint community documents]].\\
 \\
-**If you can connect the printer with OctoPrint**, skip to section 3.\\
+**If you can connect the printer by baud rate 115200**, skip to section 3.\\
 \\
 **If you can not connect the printer with OctoPrint**, continue with section 2 to update the serial driver of CH341:
@@ Line 82: / Line 93: @@
 ===b)Install your Linux kernel header package===
   sudo apt install raspberrypi-kernel-headers
-===c)Download the CH340 serial driver source code and unzip it===
+===c)Download the CH340/CH341 serial driver source code and unzip it===
   wget http://www.weedo3dprinter.com/lib/exe/fetch.php/firmware/ch341ser_linux-kernel5.4.79.zip
   unzip ch341ser_linux-kernel5.4.79.zip
@@ Line 94: / Line 105: @@
   sudo cp ch34x.ko /lib/modules/$(uname -r)/kernel/drivers/usb/serial/
   sudo depmod
-{{:octoprint:7copy.png?400|}}
+{{:octoprint:7copy.png?400|}}\\
-====3.Reboot your Raspberry Pi and Connect the printer with its baud rate====
-===a)Reboot your Raspberry Pi,then add X40 settings to the profile.
+====3.Reboot your Raspberry Pi and connect the printer with its baud rate====
+===a)Reboot your Raspberry Pi, then add X40 settings to the profile.===
+{{:octoprint:x40-octoprint-settings_1_.png?400|}}
+{{:octoprint:x40-octoprint-settings_2_.png?400|}}
+{{:octoprint:x40-octoprint-settings_3_.png?400|}}
+{{:octoprint:x40-octoprint-settings_4_.png?400|}}
+===b)Connect printer with 115200 baud rate===
+{{:octoprint:x40-octoprint-connect.png?600|}}

User Tools

Site Tools

Differences

Page Tools