Differences

This shows you the differences between two versions of the page.

--- content:printing_setting [2020/08/28 15:33]
peter
+++ content:printing_setting [2020/09/21 13:45] (current)
@@ Line 1: / Line 1: @@
-=====Set XY Zoffset For Dual Nozzles=====
+=====Download Stl File & Print Out File=====
-When the new nozzle is replaced and the belt tension of the X is readjusted, the XY offset of the nozzle will change and the XY offset needs to be readjusted. The specific methods are as follows:\\
+====1.Download STL File====
+Go through [[http://https://www.thingiverse.com/|thingiverse]] for free stl file download.\\
-====Method One:====
+{{:print_your_first_sliced_model:pasted:20200828-012411.png}}\\
-====X Coarse tune====
+Search the file you are like and download it.
-Loading two-color filament in the left and right nozzle which is easy to observe.\\
-Print the two-color test file in the TF card, the file name is **NozzleCoarseTune.gcode.**\\
+{{:print_your_first_sliced_model:pasted:20200828-012442.png}}
+====2.Load file into Wiibuilder====
+{{:print_your_first_sliced_model:pasted:20200828-012634.png}}
+====3.Set slicing parameters====
-Printer interface selection:\\
+Click Edit, click Material to select the right nozzle, and select a benefit color to simulate the color effect of the model.\\
-The 351 parameters is selected by default for printing.\\
+{{:print_your_first_sliced_model:pasted:20200828-012735.png}}\\
-{{:content:pasted:20200828-001615.png}}
+Select the slice settings. Sets the Profile, to select the material type.\\
-At the end of the print, observe the 5 test blocks and select the one with the smallest X deviation as shown in the following figure: select 3\\
+For example Profile: High Quality; Material: PLA; Layer Height:0.15mm; Printing Speed:55; infill:10% ;Temp:200\\
-{{:content:pasted:20200828-001817.png}}
+{{:print_your_first_sliced_model:pasted:20200828-013004.png}}\\
-**XY fine-tuning:**
+Slice it and save to TF card, you can see the printing time and filament used for this model\\
-**X Zoffset Set:**\\
+{{:print_your_first_sliced_model:pasted:20200828-013110.png}}\\
-Print the two-color test file in the TF card, the file name is **NozzleFintTune.gcode**.
+====4. Insert TF card to Machine and select the Gcode file printing====
-Look at 10 of the printed models that test the horizontal and vertical directions of two colors.\\
+{{:print_your_first_sliced_model:pasted:20200828-013205.png}}\\
-**Horizontal direction**: from top to bottom, select the test block with the closest overlap of the two colors in the left and right directions.\\
+{{:print_your_first_sliced_model:pasted:20200828-013225.png}}\\
-{{:content:pasted:20200828-002112.png}}\\
+You can preview information of the printing file before printing.
-{{:content:pasted:20200828-002309.png}}\\
+{{:print_your_first_sliced_model:pasted:20200828-013244.png}}\\
-**Vertical direction (front and rear direction)**: from the top down, select the test block with the closest overlap of the two colors in the front and rear direction.\\
+**Select Print**\\
+{{:print_your_first_sliced_model:pasted:20200828-013416.png}}
-{{:content:pasted:20200828-003136.png}}\\
-**Select 2 test block and switch 5 (0) to 2 (- 0.3)**\\
-The firmware parameters are set as follows: X 351; Y:-0.3\\
-{{:content:pasted:20200828-003315.png}}

User Tools

Site Tools

Differences

Page Tools